Home Company Products Documents News Contact Work with Us
 
 
 
 
Products & Services
BLASTING
PAINTING
PERSONAL PROTECTION
INSPECTION

 

Documents
News
Contact

 

 

 

Digital Surface Profile Gauge 224

 

Surface Profile

 Surface profile, Surface Roughness and Comparators

The proper and effective preparation of a surface prior to coating is essential. Making sure that the correct roughness – or profile – has been generated is essential. If the profile is too low, the adhesion of the coating to the surface will be reduced. Too high and there is the danger that the profile peaks will remain uncoated – allowing rust spots to occur.

   

Digital Surface Profile Gauge 224

   

The Elcometer 224 provides the very latest in the surface profile measuring technology for measuring profile on either flat or curved surfaces. Fast, Accurate and very user friendly, the Elcometer 224 is available with integral probe, separated probe, with or without memory & Bluetooth. 

 
 
Elcometer 123 Surface Profile Gauge
 
The average of a series of measurements provides an indication of the surface roughness and allows the surfaces to be compared as blasting proceeds.
 
 
Elcometer 223 Digital Surface Profile Gauge 
 
The Elcometer 223 is a battery operated digital surface profile gauge which measures the peak-to-valley height of a surface in a similar way to the Elcometer 123 analogue equivalent, but with the added benefit of a direct RS232 output for data logging.
 
 
Elcometer 122 Testex Replica Tape 
 
While comparators allow the estimation of surface roughness by touch and sight, the Elcometer 122 testex tape allows the user to measure the peak-to-valley height of the profile and record it.
 
 
Elcometer 124 Thickness Gauge
 
The Elcometer 124 thickness gauge is used to measure the peak-to-valley height of a surface profile formed in the Elcometer 122 Testex Tape.
 
 
Elcometer 125 Surface Comparator
 
Surface comparators allow the estimation of surface roughness by both touch and sight. These simple roughness gauges consist of 4 blasted profiles of varying roughness and are available either in a grit blasted or a shot blasted version.
 
 
Elcometer 129 Rubert y Rugotest Surface Comparators
 
Similar to the Elcometer 125, the Elcometer 129 roughness comparators are available in two models: The Elcometer 129 Rubert is available in grit and shot versions whereas the Elcometer 129 Rugotest includes the shot and grit profiles on the same block.
 
 
Elcometer 127 Keane-Tator Surface Comparator & Magnifier
 

These comparators from keane-tator are designed to be used with a magnifier. Consisting of 5 blasted profiles on displayed with the roughness value on each disc. In the middle of the disc there is a hole for the comparison to be undertaken using the magnifier. Sand, shot or grit versions available.

   

Ship´s Propeller Comparators 133

   

The Elcometer 133 have been developed with the specific profiles relating to the condition of a ship´s propeller. Two versions are available: for above water (dry dock) inspection and for inspection work carried out underwater.

   

Needle Pressure Gauge 102

   

The Elcometer 102 is designed to measure air pressure in blast and air hoses. 

   

Blast Nozzle Gauge 103

   

The Elcometer 103 measures the orifice size of an abrasive blasting nozzle. This gauge is used to determine the nozzle orifice wear which leads to low nozzle pressure and decreased efficiency in the performance of the nozzle´s venturi.

 

 
 
Print Page
Documentation

Digital Surface Profile Gauge 224
Surface Profile Gauge 123
Digital Surface Profile Gauge 223
Testex Replica Tape 122
Thickiness Gauge 124
Surface Comparator 125
Rubert & Rugotest Surface Comparator 129
Ship´s Propeller Comparator 133
Keane-Tator Surface Comparator & Magnifier 127
Needle Pressure Gauge 102
Blast Nozzle Gauge 103

 

C/ Marie Curie 68 | P.I. Mora Garay. 33211 Gijón. Principality of Asturias. Spain.  | Tlf.: +34 985308465/66 | Fax.: +34 985324630 | Contact | Legal